Видео

Do tou have or sell the 3d files for this or version 1?

Hello, excellent video, but I have a question about the battery, does it come into contact with water when it is outside the sealed cylinder??, and the light cables are not cut???. can you guide me on that thanks and regards

The music is overwhelming and interferes with all conversational aspects

Incredible

Brilliant you guys are awesome ❤

That is super rad!

I would love to buy one do you make them for people?

MY FAVORITE SUBMARINE IN MY LIFE!

250khz

MAN, I LOVE THIS SUBMARINE!!! CONGRATULATIONS!!!

Благодарю за видео

Fantastic model! The interior detail is outstanding!! 😳 what would be a great thing to do if it can be done?? Would be to do a video “fly through” of the interior using a small fibre optic endoscopic camera slowly moving through each section then SPEED IT UP😄 would look AWESOME!!

The "Front" of a Boat is the Bow Einstien...

Beautiful!!!

What are the dimensions of the table in the middle of the shop?

I would have tried something ridiculous like giving that shaft tube some heat to try to get it out all while adding too much heat and ruining the aft section of the hull 😂😂😂😂

Работа чудо! Но, что поражает, это детальность интерера и в частности, как он делал заклепки. Потрясает. Что все элементы сделаны отдельно и, по сути, макет есть набор пазлов, и каждый пазл есть нечто сногсшибательное.

Didn't work for me, the motor got oil in it and stopped working with mineral oil. And the gearbox got jammed up. I had to flush it all, then seal all edges with epoxy resin (UV cure) and the O ring on top. Works!

Full flying rudders move rudder post ahead1/2- 3/4 inch forward so post is not in center of rudder you want it closer to leading edge

I enjoy your Vids, all great fun, and explained well, i HAVE to progress further than my dynamic sub, and on 2.4!

Great video Bob. Thanks. Where can we find an antenna extension? I have the same receiver.

I'm looking for one in scale 1/72 of the Voyage to the Bottom of Seaview. Could you tell me what scale the model yoy have?

Have fun on your break , be waiting for your new videos 👌

Looking outstanding 🦾🍻

I’m really enjoying your videos Bob great content as always .

Hello to you and your family, and your wife 's maiden name was Powell, tell her hello from Kankakee Illinois USA.

KURSK REPRODUCTION‼️ LARGE SCALE AND THE HUGE JAP SUB that was Captured and SCUTTLED to Prevent THE TECH FROM FALLING INTO RUSSIAN HANDS . THE ONE THAT HELD SMALL PLANES AND COULD LAUNCH THEM.

You need a laser level to project some level lines for you.

I'm watching this for the second time, he's a true artist! Amazing work!! I purchased the movie for my 65th birthday 😂 I remember seeing it that first time at our local theater on Saturday afternoon with my sisters!! I think if my Dad could have gotten away with it, he would have been right there beside us stuffing his face with popcorn too 😂❤!! I bought it for him as a Christmas present one year, he was telling the kids to sit down and be quiet, lol 😂, we all enjoyed the show!

I bet you will be very happy when Logan gets back. Good luck with all the projects.

Sometimes a nimh battery will survive overdischarging, you should at least give it a shot. Edit: nevermind I see you did!

Beautiful work.

Der Ton ist Off

The detail and scope of this model is unbelievable. What is the young man making in the background?

Okay, i kind of need to be invited to the next R/C submariner party.

Tilting the motor down a few degrees maybe?, just coming from rc plane building

Great episode

hahahaha That face expression @8:27

On Seaquest, I suspect the motor itself may be impeding the flow, you could try moving it forward of the servos (the drive shaft could then be reversed through the mount, lengthened and run between the servos)..........this should remove it from direct flow path.......also as a rule of thumb thrust tubes.......... generally only like a 5-15% flow restriction (on non compression systems)to minimize back-pressure .....especially since flow tubes are not self-contained...............................you might, then even be able to go back to the smaller battery to cut down on forward weight reducing dive tendency. Though I suspect the front "canard" idea to be helpful and have thought about that as well........I had noticed this on your first video and wondered if it might present a problem ....... apologizes for not mentioning this sooner ........I know it would be a more complicated rework........and current adjustments may be sufficient.......... ..........I do think tail surfaces should be hinged and linked in as well though.................I hope this is useful and am looking forward to progress on this and sharks as well............ Did you and your son ever finish his Millennium Falcon build?

Easiest way to do that blanc area is with a thermoplastic moulding putty like blue stuff. It's a small block that you heat up in boiling water, when it's soft you just press it on to the object you want to copy. Cool with cold water and the mould is ready.

Good progress on the Seaquest , couple ideas: make the clear plastic dive planes active and tie them into electronics to maintain level. Steering seems slow cut some vents and build a bow (side) thruster into the underside of the nose.

In regards to the tendency to dive, consider the center of mass. Is all your ballast in the bottom, lower then the center of thrust? Raise the ballast closer to center.

Totally REMARKABLE model work. SUPERB!

Way of lowest resistance,water can get around da nozzle easyer than thru...creating pressure

This is super cool, but I was expecting it to also fly.

Amazing job Bob the lights and your paint job just incredible.

Why do you always look like you're baked? 😁

Awesome propulsor design

Can Ed post the wiring for the battery relays?

My least favorite sub